Post here for support on the OzzMaker SARA-R5 LTE-M GPS + 10DOF

Home › Forums › Forums › Technical Support for the OzzMaker SARA-R5 LTE-M GPS + 10DOF › Post here for support on the OzzMaker SARA-R5 LTE-M GPS + 10DOF

  • This topic has 63 replies, 15 voices, and was last updated 1 year ago by SimonC.
Viewing 15 posts - 46 through 60 (of 60 total)
  • Author
    Posts
  • #18758
    Mark Williams
    Keymaster

    Hi, sorry for the late response

    where do you see this message?  “/dev/ttyGSM1: no such file or directory”

    Mark --OzzMaker.com --

    #18761
    N_J_S
    Participant

    Hi Mark,

    Thanks for your reply.

    I’ve attached the output when using “tail -f /var/log/syslog” after enabling the data connection using “sudo pon”. Prior to this I have enabled multiplexing using “sudo gsmMuxd”.

     

    #18859
    byoung2
    Participant

    Hello,

    When starting gsmMuxd I see the following errors:

    2024-03-19T13:35:58.350436-07:00 backpack gsmMuxd[1960]: Modem does not respond to AT commands, trying close MUX mode

    2024-03-19T13:36:02.390414-07:00 backpack gsmMuxd[1960]: MUX mode doesn’t function.

    2024-03-19T13:36:02.393769-07:00 backpack rc.local[1959]: MUX startup failed. See syslog for details.

     

    #18860
    byoung2
    Participant

    Ok I see the error above when starting gsmMuxd is the known issue after restarting. From a cold start it works.

    #19112
    nick
    Participant

    Hello,

    I followed the guides and managed to receive an unaided gps location. I also set up the SARA-R5s internet connection (pinging google works with 4 packages, just like in the guide).

    But when I try to enable assited gps with “AT+UGPS=1,4,71” or even “AT+UGPS=1,4,1” I get the +UGGIND response as follows:

    +UUGIND: 0,71
    +UUGIND: 4,6

    According to the example script this error reflects that the board is unable to read from socket (6: Read from socket error (for AssistNow Online)).

    I am out of ideas and I dont understand what I am doing wrong.

    Thanks in advance

    • This reply was modified 1 year, 12 months ago by nick.
    #19114
    Mark Williams
    Keymaster

    Do you see a key in the output of this command?
    AT+UGSRV?

    Mark --OzzMaker.com --

    #19115
    nick
    Participant

    I get this response:

    +UGSRV: “cell-live1.services.u-blox.com”,”cell-live2.services.u-blox.com”,”6_cr63HodUWcy7bs4tjQ0w”,14,4,1,65,0,15

    #19130
    nick
    Participant

    Hello again,

    What am I supposed to do with the key?

    Cheers

    #19162
    nickldio
    Participant

    Just a quick heads up for anyone else who might come across this problem; the token that was pre-configured apparently was expired. I created an own account on thingstream.io and configured the board to use my freshly created token, now it works!

    #19350
    eric.t@proscout.ai
    Participant

    We would like to implement a wake on motion functionality with this PCB. Is there documentation for how to achieve this? We would likely need to connect an interrupt from the IMU to a GPIO on the raspberry. Any information would be helpful on this topic. Thanks

    #19416
    SimonC
    Participant

    Hello everyone,

    I’ve bene following all from your site to make the MUX working and still have this issue:

    sudo gsmMuxd
    /dev/ttyGSM0 Command Channel
    /dev/ttyGSM1 Command Channel
    /dev/ttyGSM2 GNSS Tunneling
    MUX started
    /dev/ttyGSM0 Command Channel
    /dev/ttyGSM1 Command Channel
    /dev/ttyGSM2 GNSS Tunneling
    MUX started
    -bash: /dev/ttyGSM0: Permission denied
    -bash: /dev/ttyGSM1: Permission denied
    -bash: /dev/ttyGSM2: Permission denied
    -bash: MUX: command not found

    I did the reboot, I soldered the JP1, installed, removed, re-installed. but it’s really hard to make this works. Also i rebooted the SARA R5 module with bridge of reset and GND. still nothing. Anyone found solution ? thanks a lot

    #19417
    Mark Williams
    Keymaster

    This looks to be a permission issue on the Pi OS and not a physical issue on the SARA-R5.

    Are you able to communicate with the SARA-R5 when the mux is not enabled?

    The output above looks like you tried to start the mux multiple times, is this correct?

    Mark --OzzMaker.com --

    #19418
    SimonC
    Participant

    Hello,
    Thanks for the prompt reply.

    I reflashed everything and running now the OS32 bit. also i did this upgrade: sudo apt-get install raspberrypi-kernel-headers

    Now it seems to work. Have the ppp0 Yeah.

    Now my issue is to get the GPS coordinate. I’m following this https://ozzmaker.com/using-the-gps-on-ozzmaker-sara-r5-lte-m-gps-10dof/

     

     

    1) admin@motomesh:~ $ minicom 115200 -D /dev/ttyGSM0

    Then AT = OK

    Then AT+UGPRF=2 ERROR

    SO when starting the command to see GPS coordinate ( sudo cat /dev/ttyGSM2) I have nothing. Any idea?

    I’m totally new in this kind of IOT system. Thanks!!

     

    #19419
    SimonC
    Participant

    Hello,
    Thanks for the prompt reply.
    I reflashed everything and running now the OS32 bit. also i did this upgrade:

    sudo apt-get install raspberrypi-kernel-headers

    Now it seems to work. Have the ppp0 Yeah.

    Now my issue is to get the GPS coordinate. I’m following this https://ozzmaker.com/using-the-gps-on-ozzmaker-sara-r5-lte-m-gps-10dof/

     

     

    1) admin@motomesh:~ $ minicom 115200 -D /dev/ttyGSM0

    Then AT = OK

    Then AT+UGPRF=2 ERROR

    SO when starting the command to see GPS coordinate ( sudo cat /dev/ttyGSM2) I have nothing. Any idea?

    I’m totally new in this kind of IOT system. Thanks!!

     

    #19420
    SimonC
    Participant

    Finally ofund the issue. It’s not that easy to understand but MUX was not started, thanks

Viewing 15 posts - 46 through 60 (of 60 total)
  • You must be logged in to reply to this topic.

Blip, blop, bloop…